Cruise craft 575 -585 thru hull 50b-9b transducer install

Some people have been asking me to put this up so here goes

After purchasing the new fibreglass hull i was back sourcing the best low budget, best performance sounder set up that was able to perform in depths upto 700 meters.

Starting with conversations with taylor marine in the west and in the east i had heard the Furuno 585 unit boasted excellent performance for game fishermen in deep water. The best results were coming from thru hull instalations using the 50b-9b Transducer.

Having the same sounder system from my old vessel the next step was to liase with cruise craft on hull construction and if it was possible to install the transducer where i wanted it at the stern.

With a flat surface on the keel line this install was quite simple.  

Then was to cut thru a moulded bilge liner and having a very restricted area to work in.

Next was by far the hardest. This was actually getting the nerve to cut a 160mm by 90mm oval  hole through the hull.

With that done you realize your in so deep you had better do the rest right if your ever going to go boating agian!!

Then i made an exact replica of the transducer but 3 mm larger all round.

The replica transducer was now waxed and release agent applied.

Then the replica was inserted in the vessels cut hole, flush on the front edge and 2mm lower of the rear edge so that no air pockets could ever occur under the transducer.

From there work began on the inside with me applying epoxy fibreglass matt over the replica transducer and onto the prepared inside hull with a 100mm overlap onto the hull.  Four layers of 400 chop strand mat was applied then left to cure.

When cured the replica plug was pushed out by drilling a small hole in the center and tapping out. A larger hole was now drilled in the center of the formed fibreglass housing to suit the transducer cable and the inside of the housing sanded and cleaned with acetone.  

With the housing ready for the transducer. Marine Sikaflax was applied inside the housing and on the transducer. The transducer was now pushed slowly into place and secured, letting the air bubbles escape.

The excess sika was wiped away and another 4 layers of glass applied.

Now all that was left was a quick sand and for the white flow coat to be applied , bilge pump fitted and any sika marks to be removed with acetone.

All done and left to set.

On trial the new picture was almost unrecognizable from the memory of the ground when the transducer was last transom mounted on the previous vessel! A huge improvement. And where before we were sounding in the 250's to 400's at less than 5 knots, now we were clearly seeing ground at 10knots and breaking at 15.

The last shot shows us sounding at 840meters. Faint but readable.

Anyways hope this comes to some for benifit.

BTW this is no plug for furuno. I couldnt care if it was an Nintendo.  

I also believe similar results could be achieved with other sounder systems but the wet transducer face system (through hull) is crucial.

____________________________________________________________________________

"Its a life style job"

Image Upload: 

Posts: 9358

Date Joined: 21/02/08

Reading out in 840m was

Sat, 2012-01-28 21:26

Reading out in 840m was pretty incredible!

____________________________________________________________________________

Lamby's picture

Posts: 3145

Date Joined: 04/08/09

Wow!Awesome Tony, you must

Sat, 2012-01-28 21:28

Wow!

Awesome Tony, you must have big nackers taking on that

big john's picture

Posts: 8751

Date Joined: 20/07/06

Good

Sat, 2012-01-28 21:49

 Good job south city, nice workmanship.

____________________________________________________________________________

WA based manufacturer and supplier of premium leadhead jigs, fligs, bucktail jigs, 'bulletproof' soft plastic jig heads and XOS bullet jig heads.

Jigs available online in my web store!

grayzeee's picture

Posts: 2283

Date Joined: 09/07/09

nice one tony.  ballsy stuff

Sun, 2012-01-29 07:26

nice one tony.  ballsy stuff but the results speak for themselves.    cheers for posting

____________________________________________________________________________

If I spent half as long fishing , as I do reading this bloody forum , I'd be twice the fisherman I am. 

Lucky Tim's picture

Posts: 2536

Date Joined: 28/11/07

nice post Tony, looks like it

Sun, 2012-01-29 08:55

nice post Tony, looks like it was worth all the planning and effort to get results like that. Are you running another transducer too ie 200khz or is that it?

As a side note I stopped in 700m the other day to see if I could get the bottom with my M260 in hull and got a similar pic to yours but this was on the drift or just in gear at a couple of knots.

grayzeee's picture

Posts: 2283

Date Joined: 09/07/09

just as a side question , has

Sun, 2012-01-29 11:09

just as a side question , has anyone seen the results from one of those sliding mounts for a transom  transducer??  you can shove the transducer way down deep when using it in 50khz out deep.   would that come anywhere near the performance of this?

____________________________________________________________________________

If I spent half as long fishing , as I do reading this bloody forum , I'd be twice the fisherman I am. 

Posts: 9358

Date Joined: 21/02/08

Might still get a bit of

Sun, 2012-01-29 11:39

Might still get a bit of turbulence?

____________________________________________________________________________

whipasswaverunner's picture

Posts: 181

Date Joined: 25/09/09

Very nice job there

Sun, 2012-01-29 13:44

 Looks very good, and seems to be working well. I have a M260 and also very happy.

 Out of curiosity do you have a photo of the cross section of the hull where you cut out for the transducer. Interested in the thickness of fibreglass. 

Cheers

southcity104's picture

Posts: 1659

Date Joined: 27/01/09

yeah Tim

Sun, 2012-01-29 18:34

Im also running the 200b but havent mounted it yet. With the system i have 585-mb1100 splitter it requires both trannys to be used or it will damage the mb1100 unit. Or you can do a small rewire and bypass the mb1100. My 200b in now in a small wet box as running them dry is not good either

Whip- the hull thickness was 8.5mm

____________________________________________________________________________

"Its a life style job"

Tony Halliday's picture

Posts: 2500

Date Joined: 14/06/07

 dam nicely done mate, well

Thu, 2012-02-02 13:59

 dam nicely done mate,

 

well done and great catch too!

 

Tony

____________________________________________________________________________

Tony Halliday: ~Meals on Reels ~

 It takes a strong fish to swim against the current. Even a dead one can float with it

"It is always in season for old men to learn." Aeschylus (525-456 BC)

"In a mad world only the mad are sane." Akira Kurosawa (1910-1998)